NEW QUESTION 133
Refer to the exhibit.

Drag and drop each traffic flow type from the left onto the corresponding number on the right Not all traffic flow types are used

NEW QUESTION 134
An engineer must implement a set of changes in a Cisco Nexus 9000 Series Switch so that:

Which set of actions meets these requirements?

NEW QUESTION 135
Refer to the exhibit.

An engineer is configuring a VSAN on the network Which option must be selected to create the VSAN?

NEW QUESTION 136
Refer to the exhibit. A network engineer is configuring the Smart Call Home feature on a Cisco Nexus Series Switch. An email must be generated that contains the last 100 lines of the log every time a new piece of hardware is inserted into the chassis. Which command must be added to the configuration to receive the email?

NEW QUESTION 137
Which NFS version uses the TCP protocol and needs only one IP port to run the service?

NEW QUESTION 138
Refer to the exhibit. Which two statements about the routing table of the leaf switch are true?
(Choose two.)

NEW QUESTION 139
Which two statements describe modifying Cisco UCS user accounts? (Choose two.)

NEW QUESTION 140
An environment consists of a Cisco MDS 9000 Series Switch that uses port channels. An engineer must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows are allowed to use a different link Which load balancing method should be used to accomplish this goal?

NEW QUESTION 141
A network administrator must create a Linux container on a Cisco Nexus Series Switch. The container requires 10 percent of the CPU of the switch and 1024 MB of RAM to run successfully.
Which task provides the necessary resources?

NEW QUESTION 142
Port security is enabled on a Cisco MDS 9000 series Switch. Which statement is true?

NEW QUESTION 143
Which adjacency server configuration makes two OTV edge devices located in the same site bring up the dual-site adjacency?
A)

B)

C)

D)

NEW QUESTION 144
An engineer must back up the Cisco UCS configuration. The backup job must meet these requirements:
* It must use the TCP protocol.
* Client identification must be verified before data is transmitted.
* The backup must contain all the system and logical configuration settings.
* The operations team requires that the backup file is in a human-readable format.
Which set of configurations must the engineer use?

NEW QUESTION 145
Due to new regulatory requirements from a third party, organization ABC must enable two- factor authentication for the Cisco UCS environment. The requirement is also to provide redundancy if the authentication server goes offline.
Which three authentication components must be enabled to meet this requirement? (Choose three.)

NEW QUESTION 146
A network engineer deploys a Cisco UCS C-Series Server in standalone mode. The secondary vNIC must be used if the primary vNIC fails. The server must revert to the primary vNIC if the failure is resolved in less than five minutes. Which two actions must be performed? (Choose two.)

NEW QUESTION 147
A network engineer must implement a telemetry solution to collect real-time structured data in a large-scale network. Drag and drop the actions from the left into the order on the right to implement the solution. Not all actions are used.

NEW QUESTION 148
An engineer mus! configure the remote SSH management connectivity for Cisco Nexus 9000 Series Switches to meet these requirements
* The connectivity must be permitted from a jump host with an IP address of 10 10.10 10/24
* All switches must be permitted to connect via SSH to other devices from the subnet of 10 .20.20.0/24.
Which configuration set accomplishes these requirements?

NEW QUESTION 149

Refer to the exhibit. An engineer must deploy 70 Cisco Nexus 9000 Series Switches in a new environment The requirement is to use Cisco DCNM as a management tool to deploy, manage and monitor the new switches. In addition. DCNM is configured with a zero-touch POAP feature to facilitate fabric creation Which action meets these requirements?

NEW QUESTION 150
An engineer modifies the virtual port channel domain on a Cisco Nexus 9000 Series Switch using Session Manager. Which two commands must the engineer use to confirm the configuration is valid and apply the configuration to the switch? (Choose two.)