Updated Oct-2023 Exam HPE2-T37 Dumps – Pass Your Certification Exam [Q27-Q41]

Q27. Click the option that must be configured for an HPE OneView when an HPE storage system is connected directly to an HPE Synergy frame.

Q28. You configured downlink aggregation for one of the HPE Synergy Compute Modules in an environment by placing two connections in the same Link Aggregation Group. After you made the changes to the server profile, its status changed to critical.
What can be done to fix this issue?

The teaming or bonding driver in the server OS must be configured to enable the LACP and to form the LAG correctly.

The server profile for a given HPE Synergy compute module should be reapplied, then the Compute Module should be rebooted.

Link Aggregation Group functionality should be enabled in advanced properties of the Logical Interconnect.

Ensure that the Link Aggregation Group time-out value matches the server set values.

Q29. You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?

The sFlow option must be enabled and configured.

Both FlexNlCs must be connected to the same network.

The Compute Module profile must have exactly two connections defined.

An upgrade license must be purchased and deployed.

Q30. Which parameters can be defined in a server profile template for HPE Synergy Compute Modules? (Select two.)

partition layout for servers running Linux.

IL0 IPv4 or IPv6 address.

local storage and BIOS settings.

NIC teaming setup at OS level.

network and storage connectivity.

Q31. Your customer built a sever profile for HPE Synergy Gen 10 server and configured boot mode to Legacy BIOS. Which feature Is not available for this Compute Module?

BIOS management

Workload profile

Boot from SAN

Secure boot

Q32. Click option that will allow you to select a FlexNIC function for the specified connection.

Q33. You want a server profile to be automatically applied when an HPE Synergy Compute Module is replaced.
Click the appropriate configuration option.

Q34. You try to add an HPE Primera array to HPE OneView, but you get a connectivity error. However, you can connect to the array using SSMC. What should you verify before adding HPE Primera to HPE OneView?

whether WSAPI service is enabled on HPE Primera array.

whether the appropriate license for HPE Primera Is available in HPE OneView.

whether array management using HPE OneView is enabled in SSMC.

whether there are at least two Fibre Channel networks defined in HPE OneView.

Q35. For HPE Primera, match each task with the management tool that can be used to perform it.

Q36. Refer to the exhibit.

Which statement about the logical interconnect shown is true?

For FC uplink sets, an additional uplink from second module should be added for redundancy.

The maximum supported number of the internal networks for logical interconnect is configured.

Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.

FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.

Q37. How will setting the Purpose field within the network definition of a server profile impact the network traffic?

network purpose can give higher priority for a specific type of traffic

network purpose will impact the traffic only if Virtual Connect modules are used

network purpose will define QoS within Logical Interconnect

network purpose does not affect the behavior of the network

Q38. You originally configured boot mode for HPE ProLiant Gen10 server to ‘Legacy BIOS’ in an HPE OneView server profile and deployed an operating system. A few weeks later, you change the boot mode to the ‘UEFI optimized’ to leverage some features provided by this mode.
What must you do next?

reset an il_0 management processor to activate the new boot mode for the server

reinstall an operating system, as UEFI is using different drive format than Legacy BIOS

reset BIOS settings to the defaults so UEFI settings can be applied

reset BIOS settings to the defaults through the server profile after changing the boot mode

Q39. Your customer has an environment with five HPE Synergy Composers and 15 HPE OneView appliances managing servers that run VMware. The customer is having a hard time managing their servers.
What can the customer do to simplify management of this complex environment?

deploy HPE OneView for VMware vCenter Server

deploy HPE OneView Global Dashboard

use an Ansible playbook

integrate all HPE OneView appliances and HPE Composers with Active Directory

Q40. What is the best practice when deploying an HPE OneView appliance?

Enable VMware Fault Tolerance if the appliance is deployed to a VMware hypervisor.

deploy the appliance in a hypervisor cluster that Is not managed by OneView.

Use thin-provisioning for the HPE OneView appliance to save storage capacity.

Deploy two HPE OneView appliances and configure them in HA mode.

Q41. Which statement about a server profile for an Apollo system is true?

Fibre Channel connections can be defined

UEFI optimized is the only available boot mode

Virtual WWNs and MAC addresses can be defined

Enclosure Group Is automatically selected

Updated Oct-2023 Exam HPE2-T37 Dumps – Pass Your Certification Exam [Q27-Q41]

Leave a Reply Cancel reply

HPE2-T37 Practice Tests

Related Certifications

Recent Posts

Categories

Archives