New VCEDumps NACE-CIP1-001 Exam Questions Real NACE-CIP1-001 Dumps Updated on May 13, 2024 [Q41-Q62]

NEW QUESTION 41
It is good practice for the NACE Inspector to have instrument calibration certificates available:

At all times

In the office only

In the field only

Only if the specification requires it

NEW QUESTION 42
NACE No. 4/SSPC-SP-7 is a joint standard for

white metal blast cleaning.

brush-off blast cleaning.

commercial blast cleaning.

near-white metal blast cleaning.

NEW QUESTION 43
Polymerization is the process of:

Monomers telegraphing

Monomers joining together

All thermoplastic coatings

All organic coatings

NEW QUESTION 44
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:

Chloride salt may produce a false positive

Synthetic oil or grease may not be identified

Ultra-Violet light may contaminant the surface

Presence of weld spatter may produce a false positive

NEW QUESTION 45
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?

5 to 6 mils (125 to 150 microns)

10 to 12 mils (250 to 300 microns)

8 to 10 mils (200 to 250 microns)

6 to 7 mils (150 to 175 microns)

NEW QUESTION 46
Checking is

an exposed area of the substrate or previous coat material, caused by poor application technique.

a fine crack in the surface of a coating that rarely reaches the substrate

a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.

surface breaks in the film that often result from grease or oil contamination and revel the substrate.

NEW QUESTION 47
A successful coating inspector must be able to

apply the coating with expert accuracy.

look for problems or issues during application.

advise the coating applicator on how to mix the coating.

recommend the appropriate coating technique for the job to the contractor.

NEW QUESTION 48
Upon arrival of coating materials, the inspector should

review coating contractors’ plans for storage of coating materials and confirm they meet national, local and owners’ fire and environmental regulations.

observe and document the amount of material and batch numbers.

observe aryl document that the applicator WFT at regular intervals during application.

observe and document time frame and environmental conditions between each coat.

NEW QUESTION 49
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called

cracking.

sagging.

holiday.

checking.

NEW QUESTION 50
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply

Failing to determine the base metal reading (BMR)

Rotating the dial too fast when taking measurements

Taking measurements too far from the edge of a surface

Measuring ditty, tacky, or soft films

NEW QUESTION 51
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:

True

False

NEW QUESTION 52
The least effective method of surface cleaning is most likely

water blasting.

dry grit blasting.

hand tool cleaning.

power tool cleaning.

NEW QUESTION 53
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?

Abrasive blast nozzles

Power tools

Hand tools

Airless spray equipment

NEW QUESTION 54
An inspectors personal log book should contain:

Subjective comments re ding the application team

Objective comments regarding the application work

No comments regarding the application team

The inspector’s personal opinions of the application team

NEW QUESTION 55
Stripe coats are best applied by:

Airless spray

Conventional spray

High volume low pressure spray

Brush

NEW QUESTION 56
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?

Yes, because the ‘two standards are not equivalent

No, because there is no real difference in the standards

It depends on which hand tool the Contractor selects

It depends on which power tool the Contractor selects

NEW QUESTION 57
Solvents are added to coating formulations to

dissolve binders and form liquid coatings.

provide color.

decrease film permeability.

increase film permeability.

NEW QUESTION 58
Conventional spray is a good choice when:

High production rates are required

High quality finishes are required

High transfer efficiency is required

High viscosity coatings are being applied

NEW QUESTION 59
Passivation can best be described as:

A protective metallic oxide surface layer that slows corrosion

Complete elimination pf the corrosion process

A coating layer applied to the surface to inhibit corrosion

Treating metal with a liquid inhibiter

NEW QUESTION 60
Which is a component that supplies most of the features and functions of the material?

pigment

binder

solvent

additive

NEW QUESTION 61
Inspector’s daily reports are used:
Select All That Apply

By the contractor to estimate the amount of work done that day

To provide continuity between inspectors

To aid in arbitration between the contractor and client

To help in cases of a coating failure

NEW QUESTION 62
According to SSPC PA 2 a Spot Measurement is:

A single gauge reading

The average of gauge readings taken in a 4cm (1.5 inch) circle

The overall average of all readings

The average of all spot measurements in a given area

New VCEDumps NACE-CIP1-001 Exam Questions Real NACE-CIP1-001 Dumps Updated on May 13, 2024 [Q41-Q62]

Leave a Reply Cancel reply

NACE-CIP1-001 Practice Tests

Related Certifications

Recent Posts

Categories

Archives